How to Measure for and Install Your Butt Sleeve (butt wrap)

 

Beaver News #64 – December 4, 2017

You can now order a butt sleeve (butt wrap) from us, even if you are not able to bring your firearm to the shop.

When you order your butt sleeve you’ll provide us with three measurements. This is all we need to produce your butt sleeve and we will ship it to you. Once you receive the butt sleeve you can install it on your favorite firearm yourself.

As Mark says: if you can hunt and shoot a gun, I’m sure you can do it.

We created two videos, the first video explains how you get the three measurements that you need to send along with your order. To watch the video, click on the image below:

 

The second video explains how you install the butt sleeve once you receive it from us:

 

Should you have any troubles to install the sleeve, don’t hesitate to contact us.

How to adjust the Mare’s Leg Shoulder Rig

Video

 

Beaver News #63 – November 20, 2017

In this short video, we explain how to adjust the Mare’s Leg Shoulder Rig. Even if you have not ordered one from us, this video will still give you an insight into how we make our products fully adjustable to your liking.

Find our first video about the Mare’s Leg Shoulder Rig here

Whether you are tall or short, heavy or skinny, left-handed or right-handed, our products adjust to your body and to your liking. Mark shows you where and how you can make your adjustments to position it on your body. 

He also talks about the quick disconnect on the belt connector and why he built it the way he did.

Once you feel you found the perfect fit you need to secure the Chicago screws with some Loctite and then periodically check them to make sure they are not backing off (which is common to happen). 

To watch the video, click on the image below.

How to get subdued Hardware

Video

 

Beaver News #62 – October 30, 2017

Our Motto is: You dream it – We make it and we specialize in all kinds of different items. This time, one of our clients needed to have his hardware subdued. 

To subdue these snaps and quick-release snaps Mark first heated them up with a tiger torch. He then put them into a polisher to polish them up some and to take the chroming and lacquer off. After this, the hardware is ready to have the solution put on. The final step is to oil them up and then they are all ready to go. 

To watch the video, click on the image below.

A Rig Inspired by a Movie

Video

 

Beaver News #61 – October 16, 2017

As you know, our Motto is: You dream it – We make it! so when a client came to us, asking for a rig similar like one he saw in a movie – well we accepted the Challenge 🙂 

The movie he was talking about is Two Mules for Sister Sara and he had his eye on the rig that Hogan, aka Clint Eastwood, is wearing. 

It’s a gun belt with a holster and the first thing you’ll notice is that part of it is rough-side out – meaning the rough side of the leather is out and not the smooth side. 

The belt is lined and stitched with a decorative stitch, we added our signature 3D cartridge loops to it and of course, the buckle can be easily exchanged with our chicago screw system. 

The holster is lined as well, molded and fitted to the gun, and the keeper is a buckle-keeper just like the one on the show. 

If you have an idea of something you want to have manufactured, or you’ve seen a photograph or movie of something that you are interested in, come talk to us. 

To watch the video, click on the image below.

Custom Gun Belt & Holster on drop-loop

Video

 

Beaver News #60 – September 25, 2017

Today we are talking again about a custom item: this is a gun belt with a holster that we just manufactured for one of our customers.

He wanted a 1-3/4″ belt and he wanted to have a drop-loop on it to put on the holster for his revolver. As a prospector, he goes into the woods a lot and he has a license to carry. He wanted something that is versatile and that fits his .357 magnum

Also, because he carries different equipment on his belt he found that if the belt buckle is on the left side, where it normally is on a man’s belt, it has gotten in the way of his equipment. So we manufactured the belt to his desire and put the buckle on the right side. Watch the video to see the other features on this custom rig.

To watch the video, click on the image below.

Mare’s Leg Shoulder Rig

Video

 

Beaver News #56 – July 3, 2017


You dreamed it ….. we made it. You’ve asked for it, and we deliver:

We’ve taken our normal Mare’s Leg Holster and implemented it into a shoulder rig. It comes with

  • a plain ammo plate or an ammo plate of 6 or 12 cartridge loops
  • left- or right-handed which means you can have this as a cross-draw as well.

You can adjust the harness in a way that the holster is all the way up or further down. No matter if you are a tall or a short person, you can customize the fit of your shoulder rig and holster to your liking.

This also takes the weight off the hips and puts it more on the shoulders which equalizes it out if you wear a belt with a knife on it, for example, or you are moving around a lot, you never have the gun sitting down so far.

You can have this Shoulder Rig with any of our Mare’s Leg holsters:

And last but not least, we also added (by demand) that you can switch the hammer tab from the outside to the inside, there are instructions in the video below on how to do that.

Click on the image below to watch our latest video.

Custom Project: Mare’s Leg Holster “Bear looking around a tree”

Video

 

Beaver News #55 – June 19, 2017


A quick video to show you a custom Mare’s Leg Holster we just finished.

This one goes to show so nicely our motto: You dream it – we make it.

We’ve taken our basic Mare’s Leg Holster and we specialized it to our clients’ wishes and needs and look at the result, don’t you love it?

It features:

  • a Graham Howard embossing called “Bear looking around a tree”
  • a two-tone black and brown holster
  • with fancy fringe on the side
  • a cheeky tassel  hanging down
  • 3D cartridge loops
  • Leg Strap with buckle in lieu of the leg tie

 

Click on the image below to watch the short video.

Moving the leg tie on your Mare’s Leg Holster

Video

 

Beaver News #52 – May 8, 2017

People have asked us “how do I move the leg ties on my Mare’s Leg Holster”? So we thought we make a short video about it since there is a little trick to it.

Don’t own a Mare’s Leg Holster yet?
Order yours here, you can choose between six different styles.

When you receive your hand-made, high-quality Mare’s Leg Holster from us, the leg ties are on the middle setting of the 5-holes, but you might need it higher or lower.

So how do you move them up or down?

This is what Mark explains in this short video. First Mark shows you how to figure out in what hole your leg ties should be and then how to move them there.

What you will need:

  • pliers
  • a basic paper clip
  • and a little bit of patience
  •  
    Watch the video below and let Mark show you how to do it:

    Mark carving the Grizz – part 2

    Video

     

    Beaver News #51 – April 24, 2017

    This is part 2 of our behind-the-scenes video that gives you a glimpse into how Mark carves the Grizzly that is featured on our Mare’s Leg Rig “Grizz“.

    If you missed part 1, watch it here. You’ll get to see how Mark does all the basics, the carving, the pressing and the relief and bringing the animal out by accenting the edges, like a 3D effect.

    Now in part 2 you’ll see him work on the hair. It’s a long process, as Mark mentiones, Grizzlies are quite hairy fellas :-). The longer he works on it the more you’ll see the Grizzly really coming to life, at one point it even seems to attack you through the screen….

    The next step is dying and don’t you startle at first when you see him applying the dye all over this beautiful carving? But then, all cleaned up and waxed, you’ll see how amazing it looks and at the end of the video you’ll see the hole rig all put together.

    Click ont he image below to watch this majestic animal come to life.

    Mark carving the Grizz – part 1

    Video

     

    Beaver News #50 – April 10, 2017

    This is a behind-the-scenes video that gives you a glimpse into how Mark carves the Grizzly that is featured on our Mare’s Leg Rig “Grizz“. It’s a two part series and this is part 1.

    We jump in right after Mark has traced the outlines onto the leather and used the swivel knife to cut the outline out. Now he shows you how he does the carving, the pressing and the relief, this is still all the basics, as you will see.

    Then he is bringing the carving out by accenting the edges, like a 3D effect. For that he uses a stamping tool, and the object is to using pressure, pushing down and smoothing it out at the same time, but the leather has to have just the right dampness for that.

    When he makes the hair, and highlights the hair, the carving is going to stand out like the animal is charging you with the hair all up in hackles.

    Every one of our carvings, even though there are similarities, is unique, just like every animal or every person is unique. There is not two that are identical.

     

    Tactical Knife customized

    Video

     

    Beaver News #49 – March 27, 2017

    Today we are talking about taking tactical gear, or your personal hunting gear or fishing gear, and modifying what you’ve already purchased. 

    There is a lot of good high-quality gear out there but it still may not suit your needs 100%. So one of our specialties is that we make modifications and upgrades to your gear, just like our motto says:

    You dream it  – we make it!

    In the video below we show you an example:
    One of our clients bought a Blackhawk Knife that he wants to use in a tactical way. We went ahead and wrapped the handle with rawhide. We double wrapped it meaning, first we wrapped it one way and then we wrapped it a second time crisscrossed. We also died the raw hide a nice rich brown.

    This is just one example of how we can customize or upgrade your existing gear. Come talk with us about your ideas, but first, click on the image below and watch the short video:
     

    Tactical Dog Collars and Leashes

    Video

     

    Beaver News #48 – February 27, 2017

    Let’s talk tactical.

    It’s snowing AGAIN here in the Lower Mainland, what unusual winter weather for us.

    Mark used this opportunity to pull out his winter camouflage suit so he would blend in, especially since the dog is white as well 🙂

    Today he is talking about tactical dog collars and leashes.

    • Double 9-10oz Latigo Leather
    • 1-1/2″ wide
    • Molded sewn handle with reinforced copper rivets
    • Double 1-1/2″ D-rings one on either side
    • single roller buckle

     

    The big handle is free floating and doesn’t collapse so you get your hand into it no problem, even if you are wearing gloves. So if you are in a hurry to take control of your dog, you can grab the handle right away.

    Watch the video below for more information and to see our cute 11-month-old Bianca.